A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Presented here down the page you can locate a bunch of wonderful points with regards to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult job. If the old tub is easily accessible, the job can relocate quickly; if you have to open a wall surface to eliminate the old tub and also position the new bathtub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to leave the old tub and embeded in the new one. Ensure you have actually qualified yourself for the work and also are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed job, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your bathroom if you have actually currently gotten a new bathtub as well as do not need to change the plan of your previous water system pipes.
Your tools and also product list need to consist of the following:
Planning for the Setup
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be quite problematic due to the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the needed placement. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub till the level checks out level.
To install taps, fit all-time low of the furthest versatile faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water and also examine all joints as well as new pipework for leakages and also tighten them if required. Fill the bath tub as well as also inspect the overflow outlet and also the typical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub should wait up until the tub has actually been utilized at the very least once as this will settle it into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Safeguard the faucet in place with the maker offered backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub remains in use. The sealer can fracture relatively early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the floor tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads on How to Install a Bathtub, I thought sharing that section was a good idea. Those who enjoyed reading our blog posting kindly do not forget to share it. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Emergency plumber? One call away. Report this page